Sikkens Cetol TSI Satin Plus
Available in:
1L
2.5L
From
£29.89
£28.69
Inc. VAT
£23.91
Ex. VAT
Cetol TSI Satin Plus is a medium build solvent-borne interior woodstain, for decoration and protection on smooth planed softwood and hardwood. A single product system, providing a hardwearing finish resistant to knocks, spills and abrasion. Cetol TSI Satin plus has a strong surface film, and is resistant to water and mild household detergents. Cetol TSI Satin plus can be used on floors subject to light domestic wear.For use on window frames, handrails, skirtings, wood panelling, doors, furniture etc. in coloured and colourless finishes.
Resistant to knocks,spills and abrasion
Resistant to water and mild household detergents
Can be used on floors subject to light wear
Easy to apply
Cetol TSI Satin Plus is a medium build solvent-borne interior woodstain, for decoration and protection on smooth planed softwood and hardwood. A single product system, providing a hardwearing finish resistant to knocks, spills and abrasion. Cetol TSI Satin plus has a strong surface film, and is resistant to water and mild household detergents. Cetol TSI Satin plus can be used on floors subject to light domestic wear.For use on window frames, handrails, skirtings, wood panelling, doors, furniture etc. in coloured and colourless finishes.
Resistant to knocks,spills and abrasion
Resistant to water and mild household detergents
Can be used on floors subject to light wear
Easy to apply
Description
Cetol TSI Satin Plus is a medium build solvent-borne interior woodstain, for decoration and protection on smooth
planed softwood and hardwood. A single product system, providing a hardwearing finish resistant to knocks, spills and abrasion. Cetol TSI Satin plus has a strong surface film, and is resistant to water and mild household detergents. Cetol TSI Satin plus can be used on floors subject to light domestic wear.For use on window frames, handrails, skirtings, wood panelling, doors, furniture etc. in coloured and colourless finishes.
planed softwood and hardwood. A single product system, providing a hardwearing finish resistant to knocks, spills and abrasion. Cetol TSI Satin plus has a strong surface film, and is resistant to water and mild household detergents. Cetol TSI Satin plus can be used on floors subject to light domestic wear.For use on window frames, handrails, skirtings, wood panelling, doors, furniture etc. in coloured and colourless finishes.
Technical/Safety Info.
| Product Type | Wood Stain |
| Short Description | A medium build, solvent-borne interior woodstain providing a satin finish. |
| Drying time (recoat) | 16 hours |
| Drying time (touch dry) | 6-8 hours |
| Suitable Surface | Door frames, Furniture, Doors, Skirting boards, Window frames, Wood |
| Coverage | 11 -13 m²/L |
| General No. of Coats | 3 |
| Application description | Ensure product is thoroughly stirred before and during application, otherwise sheen and colour variations may be experienced. Cetol TSI Satin plus is supplied ready for use and does not require thinning. For best results use a good quality, long-haired soft bristle brush. Three coats of Cetol TSI Satin plus should be applied, allowing a minimum of 16 hours drying time between coats. The product should be applied in a full flowing coat, laying off in the direction of the grain, using the minimum number of brushstrokes necessary to produce an acceptable finish. Avoid overbrushing, as this will produce brush marks and a poor quality finish. Apply to a minimum wet film thickness of 54 micrometres. Conditions – Do not apply when air/substrate temperatures are below 5ºC or above 30ºC during application or drying periods.Protect from water until dry. Failure to meet these requirements may adversely affect the drying, visual quality and durability of the finish. The first coat should be carefully denibbed using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction of the grain. Do not break through the surface coating. Remove all dust. Subsequent coatings should be applied as soon as possible after the previous coat has dried, but no sooner than 16 hours. |
| Cleaning | Cleaning After Final Use: Clean brushes and rollers immediately after final use to reuse them for future projects, saving you money and reducing waste. Cleaning Steps: 1. Remove Excess Product: Scrape off leftover product into a container for reuse. 2. Use Brush Cleaner: Use a Brush Cleaner to clean brushes and rollers. 3. Reuse Brush Cleaner: Allow the paint solids to settle and reuse the cleaner by pouring the clear liquid into another container. 4. Dry Naturally: Let tools air-dry and store in a dry, dust-free area. Dispose Responsibly: Dispose of the remaining solids and used brush cleaner at a hazardous waste facility. Do not pour any solvent-based paint, brush cleaner or washings down the drain or onto the ground. Do not flush paint down the drain, including when cleaning painting tools |
| Storage | Storing & Responsible Disposal Do not use or store in extreme temperatures and protect from frost. Whenever possible, reuse, recycle, or donate leftover paint. Find local services at recyclenow.com. If no Community RePaint service is nearby, consider advertising paint locally—many good causes need it to brighten community spaces. Dispose Responsibly: Never pour paint or waste washings down drains or sinks. Follow instructions at recyclenow.com to recycle empty packs. Reuse Roller Cages: Remove sleeves and store cages in a dry, dust-free place. If brushes or sleeves cannot be cleaned or reused, dispose of them in general waste to avoid recycling issues. Paint Washings: Collect used brush cleaner in a container; don't pour it into drains or on the ground. Let solids settle, pour off clear liquid into another container for reuse or disposal. Dispose of remaining solids and used cleaner at a hazardous waste facility. Do not flush paint down drains, including when cleaning tools. |