Sikkens Cetol BL Unitop
Available in:
2.5L
£67.58
£64.87
Inc. VAT
£54.06
Ex. VAT
Cetol BL Unitop is a water-borne acrylic urethane varnish which provides a satin finish.
Excellent resistance to knocks, spillages and abrasion
Non-yellowing
Low odour
Quick drying
Cetol BL Unitop is a water-borne acrylic urethane varnish which provides a satin finish.
Excellent resistance to knocks, spillages and abrasion
Non-yellowing
Low odour
Quick drying
Description
Cetol BL Unitop is a water-borne acrylic urethane varnish which provides a satin finish.
Technical/Safety Info.
| Product Type | Varnish |
| Short Description | A colourless, water-borne, protective varnish providing a satin finish |
| Drying time (recoat) | 5 hours |
| Drying time (touch dry) | 2 hours |
| Suitable Surface | Lattices, Door frames, Wood, Sidings, Doors, Smooth Sawn Siding, Rough Sawn Siding, Rails |
| Coverage | 12-18 m²/L |
| General No. of Coats | 3 |
| Application description | Conditions: Do not apply when air/substrate temperatures are below 8ºC or above 25ºC during application or drying periods. Protect from frost until dry. Failure to meet these requirements may adversely affect the drying, visual quality and durabilityof the finish. Ensure product is thoroughly stirred before and during application, otherwise sheen variations may be experienced.Cetol BL Unitop is supplied ready for use. Do not thin. For best results use a good quality synthetic-fibre brush specifically designed for the application of water-borne products. Apply the product in a full flowing coat, laying off in the direction of the grain, using the minimum number of brushstrokes required to produce an even finish. Avoid overbrushing, which creates brushmarks and will reduce the protection afforded. This initial coat should satisfy the porosity/absorption of the timber. Carefully denib the first coat using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper. Remove all dust. Three coats of Cetol BL Decor should be applied, allowing a minimum of 5 hours drying time between coats or a two coat application onto a coloured coating such as Cetol BL Decor for protection. |
| Cleaning | Cleaning After Final Use: Clean brushes and rollers immediately after final use to reuse them for future projects, saving you money and reducing waste. Cleaning Steps: 1. Remove Excess Product: Scrape off leftover product into a container for reuse. 2. Wash with Warm, Soapy Water: Clean brushes and rollers with warm soapy water in a sealed container like a bucket or tub. 3. Rinse Thoroughly: Rinse out all soap and product residues into the same container. 4. Dry Naturally: Let tools air-dry and store in a dry, dust-free area. Dispose Responsibly: Settle Solids: Let solids settle at the bottom of the container. Pour off clear water for reuse or disposal. Disposal: Let remaining solids dry fully before disposing of them as solid waste. Do not flush paint down the drain, including when cleaning painting tools Pro Tip: Watch this cleaning guide from the British Coatings Federation and Dulux Connect contractor Bagnall’s: https://coatings.org.uk/general/custom.asp?page=HowToCleanPaintbrushes |
| Storage | Storing & Responsible Disposal Do not use or store in extreme temperatures and protect from damp & frost. Reuse, Recycle, or Donate: Whenever possible, reuse, recycle, or donate leftover paint. Find local services at recyclenow.com. If no Community RePaint service is nearby, consider advertising paint locally—many good causes need it to brighten community spaces. Dispose Responsibly: Never pour paint or wastewater down drains or sinks. Follow instructions at recyclenow.com to recycle empty packs. Reuse Roller Cages: Remove sleeves and store cages in a dry, dust-free place. Dispose of Unusable brushes and Sleeves: If brushes or sleeves cannot be cleaned or reused, dispose of them in general waste to avoid recycling issues. Paint Wash Water: Collect wash water in a container; don’t pour it into drains or on the ground. Let solids settle, pour off clear water for reuse or disposal, and let solids dry before disposing as solid waste. Do not flush paint down drains, including when cleaning tools. |
Reviews
Datasheets & Downloads
Delivery
estimated delivery/collection in 3 working days