Sikkens Cetol HLS Plus

0 reviews Write a review
Available in 1L | 2.5L | 5L
Colours: Dark Oak, Ebony, Light Oak, 6 more
From
£24.42 Incl. VAT
£20.35 Excl. VAT
Cetol HLS Plus is a low build, solvent-borne, semi-transparent woodstain for use on exterior softwood and hardwood substrates such as cladding, fascias, soffits, rough sawn timber, fencing, or components subject to high levels of wear and abrasion, such as garden furniture, handrails and exterior decking. Cetol HLS plus is applied as a base stain prior to the application of higher build finishes such as Cetol Filter 7 plus or Cetol THB plus on smooth planed exterior joinery. Cetol HLS plus should not be used alone as a finish for hardwood timbers other than decking
Cetol HLS Plus is a low build, solvent-borne, semi-transparent woodstain for use on exterior softwood and hardwood substrates such as cladding, fascias, soffits, rough sawn timber, fencing, or components subject to high levels of wear and abrasion, such as garden furniture, handrails and exterior decking. Cetol HLS plus is applied as a base stain prior to the application of higher build finishes such as Cetol Filter 7 plus or Cetol THB plus on smooth planed exterior joinery. Cetol HLS plus should not be used alone as a finish for hardwood timbers other than decking

Description

Cetol HLS Plus is a low build, solvent-borne, semi-transparent woodstain for use on exterior softwood and hardwood substrates such as cladding, fascias, soffits, rough sawn timber, fencing, or components subject to high levels of wear and abrasion, such as garden furniture, handrails and exterior decking. Cetol HLS plus is applied as a base stain prior to the application of higher build finishes such as Cetol Filter 7 plus or Cetol THB plus on smooth planed exterior joinery. Cetol HLS plus should not be used alone as a finish for hardwood timbers other than decking

Technical/Safety Info.

Product Type Wood Stain
Short Description A low build, solvent-borne, semi-gloss woodstain. Can be used both as a base stain and as a finishing coat.
Suitable Surface Wood
Coverage < 14 m²/L
General No. of Coats Finishing coat - new /bare large surface areas - 3 coats Maintenance - 1 coats unless surfaces are excessively weathered Base stain - new/bare timber - 1 coat prior to Cetol Filter 7 Plus or Cetol THB Plus
Application Description Conditions : Do not apply if there is a risk of rain, or when air/substrate temperatures are below 5ºC or above 30ºC during application or drying periods. Protect from frost and rain until dry.Failure to meet these requirements may adversely affect the drying, visual quality and durability of the finish.Initial Procedure Ensure product is thoroughly stirred before and during application, otherwise sheen and colour variations may be experienced. Cetol HLS plus is supplied ready for use. Do not thin.Applying the product For best results use a good quality, long-haired, soft bristle brush. On new work, where practical, the initial coat should be applied all round prior to fixing. P ay special attention to any areas of exposed end grain, tops and bottoms of doors, and undersides of cills.The product should be applied in a full flowing coat (working well into joints, and ensuring end grains or sawn timbers are saturated with product). Excess surface material should be re-distributed after 5-20 minutes (depending on conditions), using a dry brush (which should be periodically dried with a lint-free cloth) and the minimum number of strokes required to produce an even overall colour. This ensures that the first coat satisfies the porosity/absorption of the timber. Allow a minimum of 18-24 hours drying time. Where appropriate (e.g. for joinery items such as windows and doors), the first coat should be carefully denibbed using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction of the grain. Do not break through the surface coating. Remove all dust.Cetol HLS plus should be applied in a full flowing manner in the direction of the grain, using the minimum number of brush strokes necessary to produce an acceptable finish. Avoid overbrushing, as this will reduce the protection afforded.Subsequent coatings should be applied as soon as possible after the previous coat has dried, but no sooner than 12-24 hours, in order to provide full protection. In any event this period should not extend beyond three months, otherwise additional preparation and coats may be necessary. If applied to exterior timber and the contract is of long duration, it is suggested that a further coat be applied prior to handover to make good any weathering during the construction period
Cleaning Clean brushes and equipment with brush cleaner immediately after use. If spilled, Cetol HLS plus may be removed immediately while still wet, using white spirit
Storage Store in cool, dry, frost-free conditions

Reviews (0)

There are no reviews yet.

Downloads

    AkzoNobel respects the privacy of your data

    We process personal data in compliance with GDPR. Please see our Privacy Statement for more information. AkzoNobel uses cookies to offer the basic functionality of the website, to tailor the content on social media and to generate user statistics using Google Analytics on anonymous basis to make our website more user friendly. Click on "I agree" to accept the cookies specified in the Cookie policy and go directly to the website or click on "Set cookie preferences" to indicate your preferences for cookies.

    Loading